-
HELPING
HANDS So you're trying to hold that small board, while holding the
transistor you are trying to solder, and holding the soldering iron and the
solder. Wait... that's 4 hands! It's not a problem with the Helping Hands with
Magnifier; just clip your board into the alligator clips, position your board
where you need it, and off you go! Can't see those tiny parts? It even has a
magnifying glass built in! Even has a small dish to hold a wet sponge for your
soldering tip.
2.
<--mag
pics
X-Band Military Magnetron
This magnetron operates at a peak of 40,000W (yes it says 40KW) Watt
X-band military microwave magnetron with complete spec sheets from
manufacturer and operational (DMEMPR plans) information to make it work (about 30
pages) and EMP rifle plans (over 49 pages). A device
such as this can be made the size of a super soaker water gun, it operates
between 9.345 - 9.405GHz and with a properly tuned horn antenna will have an effective range of
over 275 yards (possibly more with larger antenna). This particular
magnetron does not ship with a magnet, it requires a magnet type C1050
(details in spec sheets). The output of the magnetron is Waveguide type
RG-51/U. Such
a device could possibly cause semiconductors to burn out, microprocessors to
malfunction, inductors to counter induce and create CEMF, induce RF noise,
cause ionization of air or gases, cause junction rectification and erase
computer data on hard drives, disk and solid state device.
Operating such a device may be in violation of State or Federal Laws, consult
your Local authority before operating such a device. WE
ONLY HAVE 6 MAGNETRONS
AVAILABLE
- 250KVDC@.0001pF CAP FOR HPEMP GENERATOR WEAPON.
- ROTARY SPARK GAP FOR HPEMP GENERATOR WEAPON.
- REGULAR ADJUSTABLE SPARK GAP FOR HPEMP GEN WEAPON.
-
1000VDC Fixed Position SPARK GAP FOR HVEMPBOX, Both
Jackpot Devices and DMEMPR Kit. $15.00 for 3
- 12KV OR 36KV FULL WAVE POWER/PULSE BRIDGE RECTIFIER MODULE. RATED EXTREME DUTY. 12KV AT 6000WATT CONTINUOUS AND 24KW PEAK POWER. 36KV AT 18KW CONTINUOUS AND 72KW PEAK POWER. SILICON CASED. 1/4" SLIP CONNECTORS. NEW COST IN MARKET IS OVER $300 EACH.
Laser Parts List
The following is specifically for all laser-related items.
-
FLASHLAMP TRIGGER TRANSFORMER AND CAPACITOR SET SET INCLUDES: 15-50KV HEAVY DUTY TRIGGER TRANSFORMER AND A 1200VDC@.5uF CAPACITOR. WITH THIS SETUP YOU CAN TRIGGER ANY FLASHLAMP
ON THE MARKET. WHILE SUPPLIES LAST (WE ONLY HAVE 7 SETS FOR SALE!)
- LASER RESONATOR MIRROR SET. 99.99% BACK, 97.9% FRONT. MIRRORS VARY IN SIZE AND POWER RATING. MOST MIRRORS ARE 7MM DIAMETER MIRRORED SURFACE. ACTIVE REFLECTION IS OPTIMAL AT 632.8nm. ALL MIRRORS ARE QUARTZ FUSED TO STEEL AND CAN WITHSTAND VERY HIGH TEMPS. CAME FROM USED EQUIPMENT. DOES NOT INCLUDE MOUNT. ONE SET OF MIRRORS (NEW WOULD COST OVER $100) YOUR COST WAS $30.00.
Ruby Laser rods we may have available, please email. All rods are 1/8 inch diameter and have a semi-polished, matted finish, ends need polished. Please email for availability of the laser rods. We currently have a very large selection of rods, but hurry they will only last for short time! They are $20.00 per 3" length plus $2.00 each regular shipping. Item#Rubyrod.